Micron Electronics NetFRAME LV2000 Guia do Utilizador Página 30
- Página / 102
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
2-10 Micron Electronics, Inc.
Micron NetFRAME LV2000 Server System User’s Guide
CPU Speed Jumper
The jumper at pins 1, 2, and 3 controls whether you can configure the speed of
the processor.
Note
Depending on your configuration, this jumper is either available to set the
speed of the processor, or not available at all. If available, enabling this jumper
will activate the CPU Speed Setting field in the Main Menu of the BIOS Setup
Utility. See Chapter 3.
Procedure to enable processor speed configuration:
1. See “General Procedure to Change Jumper Setting” on page 2-6.
2. Move the processor speed jumper from pins 1 and 2 to pins 2 and 3.
This activates the CPU Speed Setting field in the BIOS Setup Utility.
3. Reinstall the side cover for your safety, and connect the power cord to
the system.
4. Run the BIOS Setup Utility as described in Chapter 3.
5. Select the proper speed for your processor.
6. Again remove the side cover.
7. Move the processor speed jumper from pins 2-3 back to pins 1-2.
8. Reinstall the side cover for your safety, and connect the power cord to
the system.
FRB Timer Enable Jumper
The jumper at pins 5, 6, and 7 controls whether the system boots from processor
1 if processor 0 fails.
Procedure to disable FRB timer:
1. See “General Procedure to Change Jumper Setting” on page 2-6.
2. Move the recovery boot jumper from pins 5 and 6 to pins 6 and 7.
3. Reinstall the side cover for your safety, and connect the power cord to
the system.
4. Turn the system on, and wait for POST to comlpete.
5. Run the SCU to configure the system. See Chapter 3.
- NetFRAME 1
- Copyright and Trademarks 2
- Safety Information 3
- Power Supply Warning 4
- Battery Warning 4
- Ergonomic Notice 5
- FCC Information 6
- DECLARATION OF CONFORMITY 7
- Table of Contents 9
- Chapter 1 10
- Setting Up Your System 10
- Unpacking 11
- Getting Started 12
- What You Need 12
- Putting It All Together 12
- Micron Electronics, Inc. 1-5 14
- Figure 1-5. Tower Case-Front 14
- 1-6 Micron Electronics, Inc 15
- Figure 1-6. Tower Case-Rear 15
- Turning Off Your System 16
- Maintenance 17
- Protecting 18
- Backing Up 18
- Removing the System Cover 19
- Micron Electronics, Inc. 1-11 20
- Chapter 2 21
- Overview 22
- System Board 23
- 2-4 Micron Electronics, Inc 24
- Jumper Settings 25
- CMOS Jumper 28
- Password Jumper 28
- Recovery Boot Jumper 28
- CPU Speed Jumper 30
- FRB Timer Enable Jumper 30
- Installing Add-On Peripherals 32
- Add-in Board Slots 33
- DIMM sizes and compatibility 34
- DIMM Modules 35
- Removing DIMM Modules 37
- Chapter 3 38
- Configuring the System 38
- BIOS Setup 39
- When Setup Should Be Run 39
- Power-on Self Test (POST) 40
- When to Run the SCU 42
- Record Your SCU Settings 42
- Six Steps in Using the SCU 44
- Add and Remove Boards 45
- To define an ISA board: 45
- Change Configuration Settings 46
- Advanced Options 46
- Save Configuration 47
- View Switch/Jumper Settings 47
- SCU Utilities 48
- Server Management 56
- Using Setup 57
- If You Cannot Access Setup 58
- How to Enter and Start Setup 58
- Setup Menus 59
- Main Menu 60
- Primary IDE Master and Slave 61
- Secondary Master and Slave 62
- Keyboard Features 62
- Advanced Menu 63
- PCI Configuration 64
- 3-28 Micron Electronics, Inc 65
- Feature Choices Description 65
- Feature Option Description 65
- Micron Electronics, Inc. 3-29 66
- 3-30 Micron Electronics, Inc 67
- Security Menu 68
- 3-32 Micron Electronics, Inc 69
- Server Menu 70
- Server Management Information 71
- Console Redirection 71
- Boot Menu 72
- Hard Drive 73
- Exit Menu 74
- Using SCSI 75
- Main Menu, SCSI 76
- Boot Device Options, SCSI 78
- Exit Menu, SCSI 83
- Installing Video Drivers 84
- Chapter 4 85
- Introduction 86
- System Problems 90
- Hard Disk Problems 93
- POST and Boot Messages 97
- Glossary 98
- C-2 Micron Electronics, Inc 99
- Appendix C: Glossary 100
- C-4 Micron Electronics, Inc 101
- About Device Drivers 102
- WARNING: 102
- Installing the Sound Drivers 102
Graco 311286C manuels
Manuels d'utilisation et guides de l'utilisateur pour Pulvérisateur de peinture Graco 311286C.
Nous fournissons des manuels en pdf 1 Graco 311286C à télécharger gratuitement par type de document : Manuel de l'utilisateur
Comentários a estes Manuais